Reset your Holosun EPS Carry Red Dot Sight

Occasionally, you may want to reset your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the adjustments or are experiencing unexpected issues. Fortunately, resetting your Holosun is a easy process that can be achieved in just a few steps.

Begin by ensuring your red dot sight is powered on.
Identify the small reinitialize button on the side of the sight.
Utilize a paperclip to depress the reset switch for approximately three milliseconds.
Let go the switch and your Holosun EPS Carry Red Dot sight will restart.
The red dot sight should now be set back to its factory settings.

Restore Your Holosun EPS Carry Red Dot back to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to go back to basics, resetting it to default configuration is a breeze. First, locate the tiny button on the side of your optic. Then, keep pressed it for around ten seconds until you see the red dot blink. Your Holosun EPS Carry is now reverted to its factory settings, ready for consistent targeting.

revive your Holosun EPS Carry Back to : Functionality

Is your beloved Holosun EPS Carry experiencing some glitches? Don't despair! A simple factory reset can often solve the problem and get your red dot sight back to its former glory. Before you begin, remember to remove the battery from your Holosun EPS Carry to prevent accidental activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these easy steps:

Hold down the power button for approximately 10 seconds.
A message will flash, indicating that the reset is in progress.
Stop pressing the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can re-attach the battery and verify your sight's functionality. If you encounter any further troubles, don't hesitate to reach out to their technical assistance.

Restore Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Adhere to these steps carefully to ensure a successful factory reset.

Beginning with, Energize your Holosun EPS Carry by pressing the power button.
Next, press and hold both the mode button and the up/down adjustment button simultaneously.
While continue holding these buttons, tap the power button once.
A message will show a confirmation prompt indicating that the reset process is initiated.
Allow the process to finish. This may take a few moments. Once done, your Holosun EPS Carry will automatically power off.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after here a reset.

Erase All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Pressing a specific button combination. Consult your Manual for the exact button sequence for your model. Once in the settings menu, look for an option that says "Reset All". Select this option and confirm the reset. Your sight will then power off and restart with all settings Returned to their default values.

Reset your Holosun EPS Carry via a Factory Original Settings

If your Holosun EPS Carry is acting funny, a factory reset might be the fix. This will restore your sight to its original settings, clearing any custom configurations you've made. To perform this reset, observe these easy steps:

To begin, locate the reset button on your EPS Carry.
Then, use a thin object, like a paperclip, to depress the reset button.
While keep the reset lever pressed, activate your EPS Carry.
It will blink a message indicating that the reset is finished.

After the reset is complete, your EPS Carry will be returned to its factory settings.